Single Arm Reels
 |
10,000 lbs. capacity powered reel with air operated, coil hold down arm and ultrasonic loop control
|
10,000 lbs. capacity powered reel
with hydraulic coil load car and air operated, coil hold down arm
|
 |
Coil Reels 15,000 - 60,000 lb. |
40,000 lb x 60" wide x 72" O.D. coil reel with hydraulic threading drive, hydraulic load car, hydraulic hold-down arm/peeler/threader and safety clock spring guard |
 |
 |
Model R-46M-12 - 6,000 Lbs. capacity pull off reel |
Back to top 

Double Arm Reels
|
| Double arm reels are ideal for continuous line operation and can drastically reduce coil change downtime. The material can be loaded and readied on one side of the reel while the opposite side is paying out stock. By depressing a shot pin in the base, the new coil of material can be rotated 180 degrees into position for threading. Optional hydraulic threading (for non-powered reels), hydraulic expansion, and hydraulic rotation are available. |
6,000 lb. capacity, 60” O.D. powered double coil reel
|
 |
DAPR-46M-30, 6,000 lb. capacity, 60” O.D. powered double coil reel
|
DAPR-46M-12, with full radius mandrel caps (optional) |
Back to top 

Cradles
Cradle/Straightener Combinations 4,000 - 40,000 lb.
 |
This unit uses standard cradle construction with a powered straightener. All of our powered straighteners have a hardened gear train, and all feature cluster gears on both the entrance and ext pinch rolls. All bottom straightening rolls are powered. Unit shown is 12,000 lb. cradle with 3.5" diameter, five-roll powered straightener. |
| |
Coil Cradles 4,000 - 60,000 lb |
|
|
|
Standard Equipment
60” or 72” diameter coil capacity, depending on model
Hardened nest rolls
Hardened pinch rolls (both rolls powered, driven by cluster gears)
Payout rate fixed at 60 FPM controlled by loop control arm
Motor and gear reducer driven
Electrical disconnect enclosure standard
Heavy steel plate welded construction
Adjustable side plates hold the coil firmly in position for continuous payout
Manually adjustable stock peeler
Optional Features
Large return stock deflectors (up to 180”)
Air-operated tip-up chutes on models up to 36” wide
Roll-down chutes in models 42” wide & wider
Crodon surfaced pinch rolls
Air cylinder operated pinch rolls in lieu of bevel gear
72” diameter coil capacity (standard on some models)
Hardened separator guide rolls in adjustable side plates
Coil end bender
Air-operated stock peeler
Heavy-duty, hydraulic peeler/breaker for thick, high strength material
Powered straighteners mounted in base
Coil hold-down arm |
|
| |

6,000-20,000 Lb. Cradles
back to top  |
| |

30,000-60,000 Lb. Cradles
back to top  |
|
Cradle Options
| Optional hydraulic tilting pinch rolls assembly enhances operator safety by enabling the operator to direct heavy-gauge material to the feed system hands free. |
 |
| Massive coil hold down arm -
suitable for containing the thickest, hardest materials |
 |
| Hydraulic peeler/breaker assembly - used for hands-free threading of thick materials.
Induces a reverse-bend allowing the lead edge of the material to be easily thread up. |
 |
| Optional precision machined roller track allows smooth flow of material though overhead deflector. |
 |
| Motorized Cabinet Height Adjustment |
|
Back to top 

Upenders
Feed Lease upenders handle 48” wide x 60” O.D. coils as standard.
Wider coils and
72” O.D. are available, and
standard capacities range from 10,000 to 20,000 lb.
Optional nylon facing for “V” block prevents possible scratching of outer coil surface.
Optional 180 degree powered horizontal rotation allows loading and unloading of coils in the same direction.
 |
The machine pictured at left is a standard 10,000 lbs. capacity upender with controls (optional 180 degree rotation and narrow coil supports are available). |
| |
|
 |
Hydraulic upenders can also be integrated into coil feeding lines to directly up end coils by indexing 90o
Three phase motor and gear box driven
|
back to top